س.ج في كل ما يخص الصيني F.A.Q of China phone Hardware and Software

س.ج في كل ما يخص الصيني F.A.Q of China phone Hardware and Software



Q1. What is format ffs?
It is the arrangement of data To comply with the phone.
After format ffs phone gets it's default state,all the user data gets
delete and bug/viruses are removed.

Q2.
What are different types of flashes?
A.NOR, PSRAM and NAND

Q3. How many
different CPU's are there in China phones ?
A.different CPUs and flash types (MTK , SPD Spreadtrum, TI Texas
Instrument, Skyworks, AD Analog Device, Infineon)


Q4. Can we list Cpu types?
A.
CPU type
6205
6217
6218
6219
6226
6227
6228
6229
6225
6223
6230....

More types

6600D
6600M
6600E6600I
6600H
6600R
6800..... etc.

Q5. What is NAND and NOR?

i)NOR:.Intel introduced the first commercial
NOR type flash chip in 1988.NOR-based flash has long erase and write
times, but provides full address and data buses, allowing random access
to any memory location.

ii)NAND:.NAND is the 2nd type of flash . It
has faster erase and write times, and requires a smaller chip area per
cell .Tt also has up to ten times the endurance of NOR flash. However,
the I/O interface of NAND flash does not provide a random-access
external address bus. Rather, data must be read on a block-wise basis,
with typical block sizes of hundreds to thousands of bits.

Q6. What is PSRAM?
A.Pseudo-Static Random Access Memory

Q7.
What are different pinouts of china phone
A.Pinouts:.
RX
tX
gnd
D+
D-
vpp
Power on

Q8. my phone is getting power on
with battery but not with Power supply?
A.Use 4.2 in power supply it will power on.Normally china phones need
more than 1100 mA current to power on that's why they need 4.2 V.

Q9. Using china tool boot loader lines run and
then stops but phone fails to power on?
A.HW fault check where the power line is broken/cut.Make jumper.

Q10. What is jumper?
A. short lenght of wire used temporarily to complete a circuit or to
bypass a break in a ciruit.

Q11. My phone
is not scanning with any tool although it's ON?
A.1.Charging jack bad soldered.(If not then)
2.Ur phne will be other than MTK and u may be trying in MTK tab .Plz try
one by one starting from speadtru, to infineon.....etc etc.

Q12. My phone was working before Flash ,after Flash
white display?
A.U have used wrong version of flash file.Downlaod correct file and then
retry

Q13. How do i come to know the
version of my Flash file?
A.Using any chinese phone tool fist scan pins and then press "phone
info" or "boot" option.It will show u the CPU version as well as
Firmware version.

Q14. In engineering mode
I enabled the High speed option .What to do now?
A.Format ur phone using any chinese phone software.

Q15. I format the phone and now it's bluetooth is not
working?
A.Repair imei or Reformat the phone.

Q16.
what is the safe method of formating phone without killing it?
A.1.Use lower baudrate and make backup before Flash.
2.Use correct erase address.

Q17. I
flashed the phone now it show's insert sim
A.First make sure u used correct flash file..If so then It's Hw fault.
Do as follows
1.Check sim tray
2.Uisng ohm-meter check those connection/lines leading to sim ic.If
broken make jumper.
3.Replace sim ic.

Q18. What is the default
password of china phone?
A.Normally 1122 if not works try 1234,3456,5678,3344

Q19. How to change china language to English?
A.Try *#0044#
If not works then try these
>Set default language: *#0000# Send
>Set English language (new firmware): *#001# Send
>***520* Change language

Q20. My phone
is short circuited .how to fix it?
A
1. Connect the phone with power supply
2. Power on it
3. Let it ON for 2 minutes
4. Lay ur thumb on different components of PCB.
5. Feel which component is getting HOT.
6. Remove that component.

Result:Check shortness should have been reduced.

Q21. DO china phones have ROM like htc?
A.NO

Q22. Can china phones be Unlocked
which are locked by some provider?
A.About 99% are not locked .They are already unlocked .
U can use any china phone to any country.

Q23.
Do my phones supports linux?
A. There is not a single china mobile in earth exists which supports
Linux.

Q24. I am going to buy China
mini-iphone or Ciphone .What's ur advice?
A.DOn't buy they are not reliable .Use original Iphone if u need.

Q25. My phone goes dead when i was changing Sim
card?
A.formatting ur phone with any professional china phone tool will ON the
phone.

Q26. I have a new double sim china
phone but it show's insert sim on both sims?
A.Enable dual sim option in menu.

Q27.
Where to find china phone codes?
A.here is the link http://depositfiles.com/en/files/ngpels7td

Q28. Where to find china phone pinouts?
A.All cable's pinouts for chines Mobiles

Q29. Where to find china phone Schematics?
A.All Chinese Models & Cloned Phones Schematics

Q30. I format the phone but it goes dead?
A. That is because u have used incorrect address 00xxxx into 0xxxxx
Use Correct address such as
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]


Q31. What is the
method now to Revive it?
A.Flash it with appropriate file.

Q32. My
sigmatel got Flight mode when my child was playing with it.
A.
Dial *### Go to Factory Settings
now click on select type sensor at last
choose gekewei and press ok. confirm it ( press ok twice )
now you are ready to use camera

OR
Without sim type*#3646633#
then you wil get eng menu
choose option 5 misc
then choose option 6 assert testing
now menu will open
then select dual mode


Q33. My phone
gets Handfree sign or earphone sign?

1.Wash handsfree jack with good solvent like petrol or CTC.

IF not solves then do as follows
2.Take Ohm-meter .

3.Attach it's one terminal to handsfree pins (one by one each) and other
to different components throughout the board especially near to
charging jack.

4. The points where the ohm-meter shows full reading or beep or Zero
resistance proves that these are the components directly connected to
hand free.

5.Once u discover those components ,check them ,change or replace.

Hope it resolve ur problem .


Q34.
Phones is not showing MMC?
adjustment Fault b/w MMC and card socket.
Plz check Mmc door or it's respective jacket (may be due to bend pins).

Q35. Bluetooth power on but fails to search?
A.Format

Q36. Bluetooth is not Powering
on?
A. Resold BlueTooth IC with good paste. Non functioning of bluetooth is a
Hardware problem.Never flash it ..or u get a dead set.[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

Q37. Phone
spk has low sound.What to do?
A.1.Increase volume from Menu or volume button.
Sound could be increase by replacing old spk with suitable Speaker.

Q38. How to format phone without Pc but with
codes?
A.try these codes
reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
reset defaults (phone/user code reset to default): *01763*737381#
KG300 NVRAM format: 2945#*# -> menu 15
SL300m reset defaults: *#987*99# Send
***000* Reset Factory settings
unlocking phone code,only press***847# without simcard

Q39. My phone is not entering in enigineering MENU?
Some phones does not carry engineering MENU due to difference in
software becoz of 62xx chip.
Ur phone lies in the same category .[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Also soetimes engineering MENU is disabled by the programmers
themselves.

Note:never enter in engineering MENU unless u know which option has what
function etc

Q40. When I insert charger
phone says "Bad contact charger".
A.This could be due to the result of excess of current drawn from the
charger.
U need required voltage/current in order to charge ur specific mobile.
Replacing charger will solve the problem .

Q41.
Camera module not ready (HW prob)
A.
1.Wash camera connectors with CarbonTetraChloride or any other solvent.
2.If not solves replace camera.
3.If still not solved replace Camera Module.

Q42. Phone is working without sim but don't completely on
with sim?
A.
Mostly china phones fails to power on completely with sim due to lack of
Current/ampere.So Check battery voltage/current with avo-meter.If
insufficient voltage/current change battery.

Q43. Boot OK but Format failed.what's the problem?
A.Reflow Flash chip.

Q44. How to reset
phone settings in case of virus ,slow working etc etc
A.Plz Reset ur phone to factory defaults.
For that go Menu > Settings > Restore factory settings >
password 1122

Q45. phone is not reading
MMC .Is it software or hardware?
A.100% HW.
Check whether ur memory card is working or not.If not replace it.If yes
then proceed as follows
1.Turn straight the bent connectors of MMC jacket.
2.Also clean MMC socket with CTC or resold it's terminals.
3.Reflow MMC IC or chnage it.
4.Reflow micro processor.(Reason:All the connections of MMC falls in
micro-processor)

Q46. I have a usb cable
can i format/flash phone with this cable ?
A.Yes but U need to modify this cable ...read more...

Q47. My phone is not playing Video?
A. 1.Try avi,mp4,3gp and other format
Try one by one and check whether it plays video or not
2.Better way is to record video and see in which format it is
saving.once u know the format of ur recorded video u will then upload
videos of the same format .
Note:.New china phones support video of.vid format.

Q48. Phone hangs after power on!!!!
A.It's a HW fault.
1.Remove Volume keys.
2.Check keypad of casing and see which has been pressed.Release that
key.
3.Phone might be water damage.Disassemble it and clean it with any
solvent.
4.Resolve MTK chip(also called micro processor)

Q49. Keypad not working.Any Solution?
A.Mostly it happens due to bad keypad connectors and sometimes due to
malfunctioning of Keypad IC.
Wash If phones is water damaged.Here is the test report http://forum.gsmhosting.com/vbb/show...82#post4783782
Try to resold keypad connectors.
Resold or Replace Keypd IC
Resold C.P.U IC (keypad connections falls in C.P.U that's y u need to
resold it while non-functioning of keypad)


Q50. I want to treat china phones and wanna be
professional in ...
U need proper equipment such as a flasher box in order to repair Ur
phone's software.

Q51. phone charging jack is broken out ,still i
want pinouts?
Mostly pinouts of sigmatel phones are printed on the PCB.
What u do is just unscrew the phone and locate it.
They consists of following contacts
rx,tx,gnd and Vpp

Q52. I am flashing a
china phone but it stops at 80% ?
first,That is normally caused due to wrong flash or communication error.
second,Try to flash with different firmware.

Q53. I can't find flash file both in support site and
forum what to do?
It's better for u to read full flash from working phone and then write
to ur's affected one.

Q54. I am making
china phone software need help about sdk,programming etc ?
A.Contact me(highlight) via pm.Will surely help u ASAP.

Q55. i want to buy china phone online?
A.Visit here www.alibaba.com

Q56. i need free china software
if u search u can find lots of free softwares in the same forum by...

Q57. My china phone is dead.How to make it
ON?
Execute this stepwise
1.Format it with correct address
2.repair security area.
3.Flash it with appropriate file
4.Do HW
In case of Hardware read this...

Q58. One
sim is working 2nd sim is emergency call?
A.Repair IMEI of secondary sim.
That's it.

Q59. phone shows no service.
Format it if not solves
Repair imei
Check Hw.Mostly bad contacts of antenna terminals.

Q60. How to locate testpoint if they r not printed on
pcb?
A.You can check available test points by multimeter
tx/rx will show voltage 2,7-2,9 volts

Q61.
My phone restarts on searching (Most common problem of chin
phones).Give solution!!
A.1.Format ffs it with any chines software (Keep backup before flashing)
s.iF not solves remove bluetooth IC.(tested in majority of phone)

Q62. How to run internet and MMS in my china
phone?
A.Make sure ur phone support these features.
If yes then ask ur service providers to send settings for that
phone.Obtain,Save,install and run ...

Q63.
How to skip calibration?
Use infinity for that
1.download and install last version of chinese miracle
2.read full flash
3.press calibrate touch screen,it will ask file give the same which u
just readed.
4.done


Q64. My sigmatel restarts,how
to solve this problem without PC?
A.Hold power key 1 minute 10 sec... with charged battery ..ur set will
formate & ask touch calibration ..do that ur set is ok now without
pc
(tested in S3)

Q65. I have no idead about
softwares ,cables etc and i want to repair my phone what should i do?
A.If u no nothing and need ur phone to be repaired instantly then visit
any Service provider or mobile software lab nearby ur house.

Q66. Ringer ,Speaker and mic all are not working?
A.Following cases are expected
1.handfree problem,read this....
2.NVRAM corrupted, if so Format phone with any chines Software.


Q67. Phone is at White display what's the
problem?
A.First of all check if u could receive or make call .
>If yes then it would be HW fault, Change L.C.D
>If no then it would be software problem
Cause:Someone might have flashed it with wrong version.
Solution: Flash ur phone with correct flash file.

Q68. After format my phone shows calibrate touch screen.
A.Make sure that touch screen is Okay.
>If yes then By pass calibration by stylus.
>If no then skip calibrtaion using infinity.For that read point 4
again.

Q69. I have no infinity box then
how can i un-calibrate my phone?
A.Flash phone with the same file and after flash neither format it nor
do restore factory setting.

Q70. How many
tools are there in market for china phone software? and which one is
best?
A.here are the list of those tools..
Spideman box
Master tool
Infinity box
Xintel/vepro
Cpf box
Among them spiderman is comparatively better due to it's fast scanning.

Q71. What is scan or spy?
A.Scan or spy is the option to find pinouts of phone.

Q72. Can i scan pinouts of original phones too apart from
china with china tool?
A.yes u can scan pinouts of original phones like alcatel and Lg etc with
any chinese phone tool.

Q73. What doeas
flash file contains?
Flash chip contains Firmware plus eeprom.
A.Firmware contains programme to run MMc,display ,to attempt call
Eeprom contains User Interface like msgs ,call logs phonebook etc

Q74.Phone fails to
install .Jar or .jad file.What is the cause?
A.Possible Reason:Your phone does not support Java or NEC emu.

Q75."not allowed to dial" problem with Cesim A9530

01. Make sure two SIMs are online with good coverage, WLAN

switched off.

02. Press the "call"-button and type in *#9646633#

03. The phone shows "Engineer mode" with a menu of 10 different

items.

04. Go to No. 10 "RF test tool", using the up/down button at the left

side of the mobile.

05. Choose "GSM"

06. A message shows up "Wifi....blabla", just confirm with OK

07. Choose "Power Scan"

08. Select your local GSM frequency (in my case DSC 1800 for

Germany) and press OK.

09. The mobile will freeze now, because its adjusting itself. Leave it
like

this for about 2-3 minutes and wait !!!

10. Connect your mobile via USB cable to a PC, DO NOT CONFIRM

any connection mode at your mobile, just and ONLY connect the

cable!!!

11. Press the Menu button (second from the left, the one with the seven

small dots on it) until you you the main menu with the 12 icons on

the display.

12. Go to "Settings" --> "Network Setup" --> "SIM1 network
setup"

13. Go to "Preferred mode" and choose "GSM preferred" or "GSM

only"


14. The mobile will switch to your selection, but the message that it

will stay on display. Do not press anything else, just wait for
about

10 - 15 seconds.


15. Disconnect the USB cable from the phone, it will show you that it

has switched to your selection.

16. Get back to main menu, switch off and restart the mobile


Q76.HOW TO SET SCIPHONE i68+ to COM MODE ?
1. Enter the engineer mode => Device => Set UART => UART
setting .
2. On TST-PS Config make it UART 2 , 115200
3. On PS config make it USB Port , 115200
4. On TST-L1 Config make it none.
5. Press Ok, the phone will shut down,
6. Start the phone, when you connect it to the computer it will be in
com-port automatically.
7. If you want the previous setting "mass storage or picture or webcam"
change the PS Config to UART 1 and press ok.


Q77.When I dial Phone show's "Check operator Services"?
A.Settings>call setup>line switching> line 2
Change line1 from line2
Done !!!

Q78.where to find pinouts?
Pinouts are printed on PCB.To find them,dismantle the phone and
locate....
For a sample I post a pic below
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

Q79.Where to download free Format/flash tool
for china phone?
http://www.4shared.com/file/10365933...ol_v38520.html


Q.HOW TO FIND RX TX SIGNALS .

I Have This Tutorial

HOW TO FIND RX TX Signal.

It is tasted and also you can test it.

1 step is, we need to find GND from phone.

2 step is, we should power on phone (operation with dead phone:
phone must be 100% dead by software)and take multimater put it to
voltage.

3 multimeter (-) line put it GND and with (+) line check each connectors
, and usually Tx= 1.8v or 2.8v and Rx=1.7v or 2.7v
(it will be change by processor but strongly 1.7v or 2.8v not 3v or 4v)
This way is too easy and you will save a more time.

(tnx to maplegsm)



Q.How to install games in China phones
A.For Installation, Apply the following Steps:

1. Go to memory card
2. Go to Games Folder (It May be GAME Also), (If Not, Create GAMES
Folder)
3. Copy *.nes Games in GAMES Folder (Visit this link or use Google to get games in .nes format)
4. Then Just Go To Fun & Games Folder
5. Restart your phone and goto Fun and Games > EMUD GAME/Games Folder
you can see Game